Looking After Your Flat Roof: Bitumen, Fibreglass and EPDM

Clean, well maintained fibreglass flat roof on an outbuilding in Goodleigh, North Devon
November 19, 2026

Flat roofs have a reputation for leaking, but most of the time it isn’t the roof that’s the problem, it’s what’s been left on it. Leaves, moss, blocked outlets and standing water cause far more failures than the materials themselves.

The good news is that looking after a flat roof is simple. Here’s what to check on the three most common types we see across North Devon, and what to avoid.

First, know what you’ve got

  • Bitumen felt: usually black or grey, often with a mineral (gritty) top layer. Laid in rolls, so you’ll see overlapping seams. Common on older garages and extensions.
  • Fibreglass (GRP): a hard, smooth, seamless surface, usually grey but available in other colours. Trims are fitted around the edges.
  • EPDM rubber: a single sheet of black rubber membrane with a slightly soft, matt feel. Usually has few or no visible seams on a domestic roof.

There are other systems too, like single ply membranes and liquid applied coatings, but the basics below apply to all of them.

Checks for every flat roof

Check: twice a year, in late autumn and spring, and after any big storm.

As with any roof, check from a ladder at the edge, an upstairs window, or inside. Don’t walk on a flat roof unless you know it’s designed for it, and never step onto old felt, a garage roof or anything that feels soft or bouncy.

  • Clear leaves, moss and debris. Anything left on a flat roof holds water against the surface and blocks the drainage.
  • Check outlets and gutters. If water can’t get off the roof, it will find another way, usually through the weakest point.
  • Look for ponding. Some small puddles that dry within a day or two are normal. Large pools that stay for days mean the roof doesn’t have enough fall. Standing water is one of the main reasons flat roofs fail early.
  • Check the edges and trims. Look for trims that have lifted, cracked or come away.
  • Check upstands and flashings. Where the roof meets a wall, a skylight or a flue is where most flat roofs leak.
  • Look inside. Check the ceiling below for staining, and if you can see into the roof void, look for damp timber.
  • Feel for soft spots. If the roof feels springy underfoot when you’re working on it, the deck underneath may be getting wet and rotting.

Bitumen felt roofs

Felt roofs are the most common type we replace. A modern torch on felt system can perform well, but older felt roofs tend to show their age.

What to look for:

  • Blisters or bubbles, which form when moisture or air gets trapped under the felt
  • Cracking or crazing on the surface, especially on south facing roofs that get a lot of sun
  • Splits along the seams, or seams that have lifted
  • Bare patches where the mineral layer has worn away
  • Felt pulling away from the edges

Small splits can sometimes be repaired, but once a felt roof is cracking all over or blistering in several places, patching it usually just moves the leak somewhere else. On a recent job in Westward Ho!, the roof had been patched over the years with fibreglass, torch on bitumen and shed felt, and water had been sitting on it. We replaced the whole thing with a new deck and better falls.

Fibreglass (GRP) roofs

A well installed fibreglass roof needs very little maintenance.

What to look for:

  • Fine cracks in the top coat, especially around edges, corners and trims
  • Cracks running in straight lines, which can point to movement in the deck underneath
  • Trims that have moved or come loose
  • Areas where the top coat has worn thin

Avoid dragging ladders or heavy items across the surface, and don’t use sharp tools to scrape debris off. A soft brush is all you need. Our guide to GRP flat roofs goes into more detail on how long they last.

EPDM rubber roofs

EPDM is flexible, tough and lasts well, but it can be damaged by sharp objects.

What to look for:

  • Punctures or tears, often from branches, dropped tools or foot traffic
  • Seams or edges where the membrane has lifted
  • Membrane pulling away at the upstands
  • Shrinkage at the edges on older roofs

Keep overhanging branches cut back and avoid putting anything sharp or heavy on the roof. Don’t use solvents or harsh cleaners, as they can damage the rubber. If you’re deciding between systems, our comparison of EPDM and GRP explains the pros and cons of each.

What not to do

  • Don’t pressure wash a flat roof. It can lift seams, damage top coats and drive water under the membrane
  • Don’t use sealant from a tube as a long term fix. It might stop a drip for a while, but it usually hides the real problem
  • Don’t stand heavy items like hot tubs, plant pots or furniture on a flat roof that isn’t designed for it
  • Don’t ignore ponding. It’s a warning sign, not just a puddle

When to call a roofer

  • Water coming in, or staining on the ceiling below
  • Splits, cracks, blisters or punctures
  • A roof that feels soft, spongy or bouncy
  • Water standing on the roof for days after rain
  • An old roof that’s been patched several times

Need your flat roof checked?

We’re accredited for a range of flat roofing systems including GRP fibreglass, EPDM, StrataPlan single ply and Elasto-Kote, so we can give you an honest view of whether your roof needs a repair or a replacement. We cover Barnstaple, Bideford, Braunton and the whole of North Devon.

Call us on 01271 359259 or get in touch through our contact page.